| Industry: | Fluid Power Generation Industry | | Project Name: | 3x 2MW 11KV container type HFO Gensets by 3 units 6L27 2000KW 750r 11kV 50HZ container generator sets | | Main Equipment Brand: | MAN | | Main Equipment Model: | 6L27 | | Origin of Product: | | | Project Progress: | 新项�?New Project | | Project Country: | | | Project Capacity: | | Summary Briefs
on the Project: | | | Project Role: | | | Bidding Or Negotiation: | | | Project Funding: | | | Payment Terms: | | | Project Type: | | | Project Start And End Time: | - | | Name Of Project Partners: | | | File Link: | NO_File |
Each set of power stations, consists of: 3units 6L27 2000KW 750r 11kV 50HZ container generator sets (. With intake module), 1unit electrical equipment auxiliary cabinet,1 mechanical equipment auxiliary cabinet, 1 unit boiler module, 2 daily oil tank 50t�?/span>by buyer�?/span> Voltage: 11KV Frequency: 50Hz Power factor: 0.8(lag) 
1.3 DESIGN CONDITION AND PERFORMANCE DAT设计条件和工作特�?/span>(1) DESIGN AMBIENT CONDITION Refer to ISO 3046 The standard environmental condition: Environmental temperature | 25�?/span> | Barometric pressure | 1bar | RH (relative humidity) | 30�?/span> | Gross Output AT Generator Terminal | 6MW | Fuel consumption at Generator Terminal | 195g/kW.h�?/span>+5% | Note: Tolerance + 5%, LCV= 42700 kJ/kg, Load 100%, 50 Hz, PF = 0.8 |
(1)设计环境条件 参�ISO 3046 标准环境条件: 环境温度 | 25�?/span> | 大气压力 | 1bar | 相对湿度 | 30�?/span> | 发电机端总输出功�?/span> | 6MW | 发电机端的燃油消耗率 | 195g/kW.h，公�?/span> +5% | 注：公差+ 5%，低热�=42700 kJ/kg�?/span> 100%负荷�?/span>50 Hz�?/span>PF = 0.8 |
1.4 FUEL OIL FOR ENGINE发动机用的燃�?/span>(1) HFO and DO The viscosity of Diesel oil shall be of�?/span>10 -15cSt at Engine inlet under the power plant operating. (1) 重油/柴油 发动机运行时的柴油机进口油的粘度应该在≥10-15cSt. Heavy oil 180 Fuel oil quality standard Item limit test method Density (15�?/span>, kg/l) not higher than 0.985 ASTM D1298 Kinematic viscosity (50 ° C, CST) not higher than 180 ASTM D445 Ash content (m/m, %) not higher than 0.10 ASTM D482 Carbon residue (m/m, %) not higher than 14 ASTM D189 Pour point (° C) not higher than 24 ASTM D97 Moisture (V/V, %) not higher than 0.5 ASTM D95 Flash point (° C) not less than 66 ASTM D93 Sulfur content (m/m, %) not higher than 3.4-.5.2 ASTM D4294/D1552 The total mechanical impurity content (m/m,%) shall not exceed 0.10 ASTM D4870 Vanadium content (PPM) is not higher than 150 ICP. 重油180燃料油质量标�?/span>
�?/span> �?/span> �?/span> �?/span> 检��方法
密度�?/span>15℃，kg/l�?/span> 不高�?/span>0.985 ASTM D1298
运动粘度�?/span>100℃，CST�?/span> 不高�?/span>34-43 ASTM D445
灰分�?/span>m/m�?/span>%�?/span> 不高�?/span>0.10 ASTM D482
残碳�?/span>m/m�?/span>%�?/span> 不高�?/span>14 ASTM D189
倾点（℃�?/span> 不高�?/span>24 ASTM D97
水分�?/span>V/V�?/span>%�?/span> 不高�?/span>0.5 ASTM D95
闪点（℃�?/span> 不低�?/span>66 ASTM D93
含硫�?/span>m/m�?/span>%�?/span> 不高�?/span>3.4-5.2 A STM D4294/D1552
总机械杂质含量（m/m,%�?/span> 不高�?/span>0.10 ASTM D4870
钒含量（PPM�?/span> 不高�?/span>150 ICP. Light diesel DO Component Unit Value Specific gravity (15°C) 0.847 Viscosity (30°C) cst 5.2 Viscosity (100°C) cst 1.0 Pour point ° C -5 Flash point °C 50 Sulfur %wt �?/span>0.5 Water %wt 0.02 Sodium ppm 1.90 Potassium ppm 2.40 Vanadium ppm 3.17 Low calorific value Kcal/kg 10140 Dust %wt trace. 轻柴�?/span>DO Component Unit Value 比重 (15°C) 0.847 粘度 (30°C) cst 5.2 粘度 (100°C) cst 1.0 倾点 °C -5 闪点 °C 50 �?/span> %wt �?.5 �?/span> %wt 0.02 �?/span> ppm 1.90 �?/span> ppm 2.40 �?/span> ppm 3.17 低热�?/span> Kcal/kg 10140 灰尘 %wt 微量
LC_Guid: |
Buyer
Inquiry Basket
Supplier
Register